Differences

This shows you the differences between two versions of the page.

--- wiki:sns:intactgh:results [2024/02/06 13:39] – [Solution Sampler] goldy
+++ wiki:sns:intactgh:results [2025/09/17 14:03] (current) – [Visualize] goldy
@@ Line 1: / Line 1: @@
 ~~NOTOC~~
 ======Results and Visualization ======
+===== Applied & Reaction Loads =====
 <WRAP group>
 <WRAP half column>
-All Results can be viewed using the Visualization Block.
-The visualization block accepts the following three inputs:
+A panel can be attached to a [[wiki:sns:intactgh:stress_solver|Stress Solver]] 'L' output to see the total applied loads/moments and total reaction loads/moments for a given stress simulation.
+</WRAP>
+<WRAP half column>
+{{ :wiki:sns:intactgh:stress_solver_loadspanel.png}}
+</WRAP>
+</WRAP>
+===== Visualize =====
+<WRAP group>
+<WRAP half column>
+All Results can be viewed using the **Visualize** Block.
+The visualization block accepts the following four inputs:
   * the simulation to be viewed as the output from a [[wiki:sns:intactgh:solvers|solver block]] or [[wiki:sns:intactgh:results#Simulation Reader|loaded from a previous simulation]]
   * deflection scale
   * [[wiki:sns:intactgh:results#Visualization Settings|visualization settings]]
+  * a clipping plane GUID from Rhino, to sample/visualize the clipping plane intersection. For more info, see❓[[wiki:sns:intactgh:faq#Results and Visualization|Frequently Asked Questions]]
+📌See [[wiki:sns:intactgh:results#Visualization Hints|Visualization Hints]] for how to hide geometries that are interefering with visualization and how to get scaled deflection
 </WRAP>
@@ Line 15: / Line 32: @@
 </WRAP>
 </WRAP>
 ===== Simulation Reader =====
@@ Line 33: / Line 52: @@
 ===== Visualization Settings =====
 <WRAP group>
 <WRAP half column>
-A Visualization Settings block allows configuring the display of the visualization.
+The **Visualization Settings** block controls how simulation results are displayed.
+It has three main inputs:
-The inputs are the maximum and minimum fraction of the full scale of the quantity you want to visualize, and an index indicating a different legend color scale to use. The defaults are to visualize the full range of the quantity of interest, and the default color scale is a rainbow color scale.
+  * **Lmin / Lmax** – minimum and maximum fraction of the full result range to show.
+    *Example:* to display only the middle 50% of the result values, set ''Lmin'' = 0.25 and ''Lmax'' = 0.75.
-For example, to visualize the middle 50% of range of the quantity of interest, set ''Lmin'' to 0.25 and ''Lmax'' to 0.75.
+  * **Li (Legend ID)** – selects the color scale used for visualization. Each integer value corresponds to a preset colormap (see legend image below).
+  * **Show Glyphs** – a toggle to enable or disable the display of boundary condition glyphs.
+**Defaults:**
+Full range of the result (''Lmin'' = 0, ''Lmax'' = 1), rainbow color scale (''Li'' = 0), and boundary condition glyphs hidden.
 </WRAP>
 <WRAP half column>
-{{ :wiki:sns:intactgh:vizsettings.png?200}}
+{{ :wiki:sns:intactgh:vizsettings.png?200 }}
 </WRAP>
 </WRAP>
+----
+**Legend ID Reference**
+Each ''Li'' value corresponds to one of the predefined color scales shown below:
+{{ :wiki:sns:intactgh:combinedoutput.png?500 | Color map legends by ID }}
 ===== Solution Sampler =====
@@ Line 53: / Line 89: @@
   * a material input in the case of an **assembly of components with different materials**.
 <WRAP center round important 80%>
-Note that using incorrect material will result in wrong results.
+Note that using incorrect material will yield wrong results.
 </WRAP>
 .
@@ Line 60: / Line 96: @@
   * a tree of solution values at the input points
   * a list of the corresponding points where the sampling occurred (these points may or may not correspond identically with the input points)
-<WRAP center round box 60%>
+<WRAP center round box 80%>
 📌 See an example problem: [[wiki:sns:intactgh:ex_7|Sampling Custom Points]]
 </WRAP>
@@ Line 71: / Line 107: @@
 ===== Visualization Hints =====
-** Z-fighting ** Visualization of results is best performed with the original geometry on a hidden layer or in Rhino viewports that are in wireframe mode.  This avoids the z-fighting that occurs when Rhino draws both the original geometry and the simulation results.
+Note: you may have to hide other geometries that interfere with the result visualization (** Z-fighting **) and also use Wireframe mode. Other geometries may have been added through Grasshopper (hide by **turning off Preview** for the GH block) or through Rhino (using Rhino's **Hide** command)
+{{ :wiki:sns:intactgh:8-_visualize_results.mp4?750 |}}
+Usage of deflection scale to animate the part deflection.
+  * Scale the deformation to see the deflected shape
+{{ :wiki:sns:intactgh:9-_post_process_deflection_.mp4?750 |}}
 ** Previews ** In the same vein, the inputs to the simulation (components, loads, and restraints) can have their previews turned off to avoid their geometry interfering with the visualization of results.
@@ Line 95: / Line 138: @@
   * **Danger Level.** For a specific failure criterion, a danger level is a scalar value that ranges between 0 and 1. It is computed at every point as a ratio of the computed value of the selected failure criterion to the threshold value known to cause failure of the particular material. A value greater than 1, indicates that the computed value exceeds the known threshold.
+      * A value greater than 1, indicates that the computed value exceeds the known threshold.
+      * The values of danger level greater than 1 are not displayed, but the maximum value and location is included in the report and may be determined in the View tab