wiki:sns:snspro:using_wood_materials
Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
wiki:sns:snspro:using_wood_materials [2017/07/12 12:16] – created zach | wiki:sns:snspro:using_wood_materials [2023/12/13 13:43] (current) – [Related Videos] michael | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ===== Using Wood Materials ===== | + | ~~CLOSETOC~~ |
+ | {{TOC: | ||
+ | \\ | ||
+ | ====== Using Wood Materials | ||
- | Scan& | + | Scan& |
- | **Important Note:**The material coordinate system convention used by Scan& | + | **Important Note:** The material coordinate system convention used by Scan& |
- | ==== Wood Material Tab ==== | + | {{ : |
+ | |||
+ | |||
+ | ===== Wood Material Tab ===== | ||
The material selector contains a tab listing the available wood materials. The grain orientation may then be specified using one of these 4 options: | The material selector contains a tab listing the available wood materials. The grain orientation may then be specified using one of these 4 options: | ||
Line 13: | Line 19: | ||
* [Specify] | * [Specify] | ||
* [Guide] | * [Guide] | ||
- | |||
- | {{: | ||
The [Rift Sawn] and [Flat Sawn] options use the principal volume moments of inertia of each component to identify the directions for axis 1, 2, and 3 of the wood coordinate system. When the principal moments are indistinct, the user is prompted to select the origin and axis directions manually. The [Specify] and [Guide] options allow arbitrary grain orientations to be specified by choosing points or geometry to guide the coordinate system creation. Use of each of these options is described below. | The [Rift Sawn] and [Flat Sawn] options use the principal volume moments of inertia of each component to identify the directions for axis 1, 2, and 3 of the wood coordinate system. When the principal moments are indistinct, the user is prompted to select the origin and axis directions manually. The [Specify] and [Guide] options allow arbitrary grain orientations to be specified by choosing points or geometry to guide the coordinate system creation. Use of each of these options is described below. | ||
Line 27: | Line 31: | ||
Use the [Rift] button to point the wood grain (axis 1) along the component' | Use the [Rift] button to point the wood grain (axis 1) along the component' | ||
+ | |||
+ | [[#Using Wood Materials|Back to Top]] | ||
==== Flat Sawn ==== | ==== Flat Sawn ==== | ||
Line 47: | Line 53: | ||
- Select a point in a direction along the grain relative to the origin chosen in Step 1 - point 2 in the figure above. | - Select a point in a direction along the grain relative to the origin chosen in Step 1 - point 2 in the figure above. | ||
- Last, select a point in the radial direction (direction of wood growth) - point 3 in the figure above. | - Last, select a point in the radial direction (direction of wood growth) - point 3 in the figure above. | ||
+ | |||
+ | [[#Using Wood Materials|Back to Top]] | ||
==== Guided Grain Direction ==== | ==== Guided Grain Direction ==== | ||
Line 61: | Line 69: | ||
- Select a guide surface - point 2 in the figures above. | - Select a guide surface - point 2 in the figures above. | ||
- | ==== Displaying Wood Coordinate System ==== | + | ===== Displaying Wood Coordinate System |
- | To allow visual verification of the grain specification, | + | To allow visual verification of the grain specification, |
{{: | {{: | ||
+ | |||
+ | [[#Using Wood Materials|Back to Top]] | ||
+ | |||
+ | \\ | ||
+ | \\ | ||
+ | ===== Related Videos ===== | ||
+ | |||
+ | <WRAP group> | ||
+ | <WRAP half column> | ||
+ | {{youtube> | ||
+ | |||
+ | {{youtube> | ||
+ | </ | ||
+ | <WRAP half column> | ||
+ | {{youtube> | ||
+ | |||
+ | {{youtube> | ||
+ | |||
+ | </ | ||
+ | </ | ||
+ |
wiki/sns/snspro/using_wood_materials.1499883392.txt.gz · Last modified: 2017/07/12 12:16 by zach